Anycubic Kobra S1 vs Bambu Lab P1S

Verdict: IT DEPENDS
Anycubic Kobra S1 vs Bambu Lab P1S: 3D printer comparison

Some links on this page are affiliate links. If you buy through them I may earn a small commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.

If you mostly print in one color and want a fast, quiet, enclosed printer with a hotter hotend, the Anycubic Kobra S1 is a strong pick, especially when it’s discounted. If you want the most polished, hands-off experience and plan to print in multiple colors often, the Bambu Lab P1S is still the safer choice. Both are enclosed CoreXY machines with similar build volumes, so the decision comes down to software, multicolor workflow and how much tinkering you’ll tolerate.

This comparison draws on the official specs and on reviews from Tom’s Hardware, TechRadar and Creative Bloq.

General overview

Feature Anycubic Kobra S1 Bambu Lab P1S
Launch price (US) Check the current price $699 ($949 with AMS)
Max print speed 600 mm/s (300 mm/s recommended) 500 mm/s
Motion system CoreXY CoreXY
Build volume 250 × 250 × 250 mm 256 × 256 × 256 mm
Enclosure Fully enclosed Fully enclosed
Max nozzle temperature 320°C 300°C
Max bed temperature 120°C 100°C
Auto bed leveling Yes (LeviQ 3.0) Yes (fully automatic)
Filaments PLA, PETG, TPU, ABS, ASA Ideal: PLA, PETG, TPU, PVA, PET, ABS, ASA; capable: PA, PC
Multicolor add-on ACE Pro: 4 spools, 8 with two units, with filament drying AMS: 4 spools, up to 16 with four units
Camera Built-in, with timelapse and AI failure detection Built-in chamber camera for monitoring and timelapse
Slicer Anycubic Slicer Next Bambu Studio
Noise Anycubic quotes as low as 44 dB in quiet mode No official figure; has a Silent speed mode

A note on versions: both brands also sell bundles with newer feeders (ACE 2 Pro and AMS 2 Pro), and Bambu has released the P2S as the P1S’s successor while still selling the P1S. Check which bundle you’re comparing.

Speed and print quality

On paper, the Kobra S1 is faster, with a 600 mm/s maximum against the P1S’s 500 mm/s. In practice, neither runs at its headline speed on most prints. Anycubic itself recommends 300 mm/s for everyday use, and cooling and material limits matter more than top speed.

Print quality is excellent on both, thanks to rigid CoreXY frames and enclosed build chambers. The P1S has the edge out of the box, particularly with Bambu filament and Bambu’s ready-made profiles, which is a big part of why Tom’s Hardware called it a new standard for 3D printing. The Kobra S1 gets very close, and reviewers praised its precision and fast single-color prints, but you may need to tweak settings more for unusual materials or multicolor jobs.

Setup and ease of use

Both printers are designed to go from box to first print quickly, and Bambu quotes around 15 minutes of setup for the P1S. Bed leveling and calibration are automated on both.

The bigger difference is software. Tom’s Hardware summed up the Kobra S1 as a good printer held back by a bad slicer. Anycubic Slicer Next works, but it’s less polished than Bambu Studio, especially for multicolor prints, and the camera view inside it is small. Bambu Studio, plus the Bambu Handy app and the MakerWorld model library, makes the P1S feel like a “plug-and-print” appliance. If you’d rather never think about your slicer, that matters.

Multicolor and multi-material printing

  • Kobra S1 with ACE Pro: one ACE Pro holds four spools, and you can link two for eight colors. A nice bonus is that the ACE Pro can actively dry filament while it prints, which helps with moisture-sensitive materials. The weak spot is the slicer’s color-change and purge handling, which is less refined than Bambu’s. It’s great for occasional color prints, less ideal for frequent, high-volume multicolor work.
  • P1S with AMS: each AMS holds four spools, and you can connect up to four units for 16 colors. Color changes are well integrated into Bambu Studio, and the ecosystem is more mature. The standard AMS doesn’t dry filament, so keep spools in a dry box if you live somewhere humid.

Both systems waste some filament on every color change, so expect a pile of purged plastic either way.

Materials

The enclosed chambers on both printers help with ABS and ASA, which warp easily in open printers. Neither has active chamber heating, but Tom’s Hardware found the Kobra S1 holds chamber heat well.

The Kobra S1’s 320°C hotend and 120°C bed give it more headroom on paper. Anycubic officially lists PLA, PETG, TPU, ABS and ASA. Bambu rates the P1S as ideal for PLA, PETG, TPU, PVA, PET, ABS and ASA, and capable of PA and PC. Bambu doesn’t recommend carbon or glass fiber filaments with the stock stainless steel nozzle, so you’d need a hardened nozzle for those.

Noise and where to put it

  • Kobra S1: Anycubic quotes as low as 44 dB in quiet mode and 46 dB in standard mode, measured at one meter. That’s helpful in a home office or bedroom.
  • P1S: Bambu doesn’t publish a noise figure. It has a Silent speed mode that slows printing to reduce noise, but the AMS and purging are noticeable in a small room.

Fast CoreXY printers shake a flimsy table, so put either one on a solid surface. If you’re setting up a corner workspace, my budget L-shaped desk picks cover sturdiness and size.

Reliability and maintenance

  • Kobra S1: reviews are mostly positive on the hardware. Creative Bloq ran into problems with its first unit, but the replacement worked well, and its verdict was that the S1 isn’t quite a Bambu Lab killer but is excellent for the price. Tom’s Hardware found the AI failure detection overly sensitive.
  • P1S: reliable and consistent, with a big user community and plenty of spare parts. The trade-off is that you’re inside Bambu’s closed ecosystem for parts, the AMS and the software.

Both printers’ cameras let you check prints remotely and record timelapses. If you end up with a big collection of models and timelapse videos, a home NAS like the one in my UGREEN NASync DXP4800 Plus review is a tidy way to store them.

Choose the Anycubic Kobra S1 if you:

  • Want fast, quiet, high-quality single-color prints.
  • Don’t need complex multi-material setups very often.
  • Like the idea of a feeder that dries filament as it prints.
  • Are comfortable tweaking slicer settings now and then.

Choose the Bambu Lab P1S if you:

Bambu Lab P1S 3D Printer, Ready-to-Use FDM 3D Printer | Beginner-Friendly Ecosystem with MakerWorld Model Library, Enclosed CoreXY, High Speed & Precision Printing
  • Up to 16 Colors: Bring your designs to life with vibrant multi-color/multi-material printing capabilities, perfect for showcasing your creativity. Note: Connecting Bambu Lab AMS is required.
  • 500mm/s and 20000 mm/s² Acceleration True High Speed: Don’t wait around for your masterpieces. Lightning-fast printing speed lets you focus on creating, not waiting.
  • Enclosed Design: Fully enclosed body improves print performance for advanced filaments. Automatic Bed Leveling: Say hello to high-quality, successful prints. Auto bed leveling makes 3D printing such an easy thing.
Check price on Amazon
  • Want a reliable, polished experience out of the box.
  • Plan to print multicolor or multi-material projects frequently.
  • Prefer automated everything, from bed leveling to filament handling.
  • Don’t mind a closed ecosystem with proprietary parts and software.

Final verdict

If you’re a hobbyist or small business focusing on fast, clean, mostly single-color prints, the Kobra S1 is hard to beat, especially when it’s on sale.

If you want a set-it-and-forget-it machine that just works, especially with multicolor or smart features, the P1S is the better option. Prices on both change often, so check the current price before you decide.

FAQ

Is the Kobra S1 faster than the Bambu Lab P1S?

On paper, yes: 600 mm/s maximum versus 500 mm/s. In real prints the difference is small, because cooling, acceleration and material limits matter more than the top speed.

Which printer is better for multicolor printing?

The P1S with the AMS. It supports up to 16 colors with four AMS units and its color changes are better integrated into the slicer. The Kobra S1’s ACE Pro handles up to eight colors and can dry filament, but its slicer is less refined.

Which one is quieter?

The Kobra S1. Anycubic quotes as low as 44 dB in quiet mode. Bambu doesn’t publish a figure for the P1S, and its AMS color changes and purging add noticeable noise.

More from my comparisons notes ↓

  1. Comparisons

    Veo Cam 3 vs XbotGo Chameleon – My Long-Term Review of Both

    For reliable, hands-off match recording, I trust the Veo far more.

    Verdict: VEO CAM 3
  2. Comparisons

    Velotric Discover 2 vs Aventon Level 3

    Hills or cargo? Get the Velotric. Park in the city and fear theft? Aventon.

    Verdict: IT DEPENDS
  3. Comparisons

    Comparing the WiiM Amp Ultra to the Sonos Amp

    Like to tweak your sound? Get the WiiM, unless you're all in on Sonos.

    Verdict: WIIM AMP ULTRA